Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 98

Страница: 98 / 128

SIREMOBIL Iso-C

SPR2-230.061.01

Page 32 of 48

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

6 - 32

Replacing boards / replacing components

Language

Set for language of the country.

Display of realtime clock

Configure Yes. Select No only upon customer request.

Display of rotated images

Configure Yes.

Monitor zoom

Configure No.

Monitor split

Configure Yes.

Monitor text

Configure Yes.

Maximum image number

Configure 900.

Disable doserate selection
in user setup

Set to "No" when equipped with an area dose product mea-
surement device. The menu "Storage of Dose on disk" and
the menu "Dose on Hardcopy output" in User Setup are vis-
ible. Otherwise set to "Yes".

Unit serial number

Program the serial number of the SIREMOBIL.
Do not enter the leading zero.

Product name

Program "SIREMOBIL Iso-C".

Software backward compati-
ble

Configure No.

Default program change-
able

Default: Yes.
Depending on country specific regulations configure Yes or
No.

Create external disk

If the option "3D Reconstruction" or the option
"DICOM Bridge" is installed or a MOD drive is present, con-
figure Yes. Otherwise configure No.

Enable Bridge

If the option "3D Reconstruction" or the option
"DICOM Bridge" is installed or a MOD drive is present, con-
figure Yes. Otherwise configure No.

Delay 3D-PC/ DICOM
Bridge

Only available of if option "3D Reconstruction" is installed.
Configure 120.

Interface to 3D-PC

Only available if option "3D Reconstruction" is installed.
Configure yes.

Default LUT

Configure 2. Only upon customers request program a
different LUT curve.

Default Edge

Configure 1. Only upon customers request program a
different Edge enhancement curve.

Default LUT for Subtraction

Configure 1. Only upon customers request program a
different LUT curve.

Subtraction K-Factor,
phase A

Program "32". Program a different value only upon cus-
tomer request.

Subtraction K-Factor,
phase B

Program "MD 2". Program a different value only upon cus-
tomer request.

Subtraction Time of phase A Program "4,5".

Program a different value only upon customer request.

Roadmap K-Factor, phase A Program "32" .

Program a different value only upon customer request.

Содержание SIREMOBIL Iso-C

































































































































Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы:

Siemens SIREMOBIL Iso-C, Инструкция по эксплуатации, Страница: 98 / 128

Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы: