Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 122

Страница: 122 / 128

SIREMOBIL Iso-C

SPR2-230.061.01

Page 8 of 10

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

7 - 8

Brakes / Movements

Emergency off switch

•

Loosen the cover above the horizontal carriage.

•

Unsolder the emergency off switch.

•

Replace the emergency off switch.

•

Solder the wires on the emergency off switch.

•

Reinstall the cover on the horizontal carriage.

•

Check functioning of the emergency off switch.
- Emergency off switch pressed: vertical lift must not be possible.
- Emergency off switch released: vertical lift must be possible.

Lubricating the lifting column

Lubricate the spindle of the lifting column and the mounting of the guide cylinder once a
year.

Spindle

•

Lubricate the spindle with approximately 10 - 20 ml of "Optimol, Optipit" special oil.

Guide cylinder

•

Grease the guide cylinder with approximately 5 - 10 ml of special bearing grease
"Slick Pac PTFE" .

•

Then move the lifting column through the entire travel range twice to ensure that the
grease is evenly distributed.

Fig. 8

Spindle

Guide cylinder

Содержание SIREMOBIL Iso-C

































































































































Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы:

Siemens SIREMOBIL Iso-C, Инструкция по эксплуатации, Страница: 122 / 128

Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы: