Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 128

Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 60

SIREMOBIL Iso-C

SPR2-230.061.01

Page 24 of 30

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

5 - 24

Adjustments / Programs

Dose measurement

5

•

Press the >0< key twice to reset the area dose product on the SIREMOBIL monitor to 0 .

•

Reset the dose measurement device (Dali, Nomex ...) to 0 .

•

Release fluoroscopy for approx. 20 seconds (~ 3 mGy). The measured dose K

E

should

be high enough that the uppermost measurement range of the dose measurement de-
vice (Dali, Nomex...) is utilized fully; if necessary, reset the area dose product display on
the SIREMOBIL and the dose measurement device and repeat the measurement with a
different fluoroscopic time.

•

Record the measured dose.

•

Record the area dose product, displayed on the SIREMOBIL monitor (FDPa).

Calculating the area dose product

5

•

To calculate the measured area dose product :
(measured area dose product FDPg) = (measured dose K

E

) * (inner diameter)

2

* 0.829.

«
...
58
59
60
61
62
...
»

Содержание SIREMOBIL Iso-C

































































































































Отзывы:

Нет отзывов