Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 128

Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 43

Adjustments / Programs

5 - 7

Siemens AG

SPR2-230.061.01

Page 7 of 30

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

•

Use the

key to select the dose rate (LOW / MID / HIGH, shown in the "DOSERATE"

line).

•

Apply fluoro briefly until the generator finishes regulating the automatic fluoro adjust-
ment.

•

Select KV STOP at the system operating console.

•

Switch on fluoro.

•

Set the dose rate with the [+kV] and [-kV] keys. (Dose rate * grid correction factor).

•

The resulting KV value should be between 70 to 80 kV. If necessary, change the prefiltra-
tion and set the dose rate again using keys [+kV] or [-kV]. Refer to the table.

•

Switch off fluoro.

•

Remove the dose measurement chamber from the I.I. input screen.

•

Switch on fluoro.

•

Press the [>0<] at the system operating console. This starts the automatic adjustment
procedure for the TV- iris collimator.

•

Wait until the message "done" appears in the "AUTO REGULATION" line.

•

The "BRIGHTNESS DEVIATION" value is shown in the "BRIGHTNESS DEVIATION"
line and should be 0 + 3 .

•

Switch off fluoro.

Setting the dose rate for zoom format

5

refer also to notice on previous page

*

•

KV-STOP remains selected.

•

Center the dose measurement chamber on the I.I. input screen and attach.

•

Select the I.I. zoom format (refer to "I.I. ZOOM STATUS"). The KV values remain the
same. The mA values, however, are automatically increased by a factor of 1.41.

•

Use the [mA+] and [mA-] keys to set the dose rate for the zoom format (Dose rate *grid
correction factor).

•

Press the [>0<] key at the system operating console. This starts the automatic adjust-
ment procedure for the TV-iris collimator.

•

Wait until the message "done" appears in the "AUTO REGULATION" line.

•

The "BRIGHTNESS DEVIATION" value is shown in the "BRIGHTNESS DEVIATION"
line and should be 0 + 3. Refer also to notice on previous page

*

•

Switch off fluoro.

•

Select the next level of dose rate (LOW / MID / HIGH) and repeat the dose rate setting for
the survey and zoom format for this level.

«
...
41
42
43
44
45
...
»

Содержание SIREMOBIL Iso-C

































































































































Отзывы:

Нет отзывов