Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 91

Страница: 91 / 128

Replacing boards / replacing components

6 - 25

Siemens AG

SPR2-230.061.01

Page 25 of 48

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

•

Configure the following parameters in User setup for MEMOSKOP:

•

Perform the IQ quick test.

Maximum image number

n.a.

Disable doserate selection
in user setup

Program for "No" when equipped with an area dose product
measurement device. The menu "Storage of Dose on disk"
and the menu "Dose on Hardcopy output" in User Setup are
visible.
Otherwise set to "Yes".

Unit serial number

Program the serial number of the SIREMOBIL.
Do not enter the leading zero.

Product name

Program "SIREMOBIL Iso-C".

Default program change-
able

Default: Yes.
Depending on country specific regulations configure Yes or
No.

Software backward com-
patible

Configure "No".

Operating mode Para-
meters

Change the parameters programmed for the organ program
upon customer request.

VCR output

Configure to Monitor A.

Hardcopy Release

For SIREMOBILwith 1 monitor: Configure to monitor A.
For SIREMOBIL with 2 monitors: Configure to monitor B.

Text monitor

For SIREMOBIL with 1 monitor: Configure to monitor A.
For SIREMOBIL with 2 monitors:
Configure to both monitors.

Split Screen

Configure horizontally. Configure vertically only upon cus-
tomer request.

Display of time

Configure Yes.

Set Date Time

Set the current date and time.

Hospital Name

Program the hospital name.

Storage of Dose on disk

If the area dose product meter is present, (Diamentor) con-
figure Yes. Otherwise, configure No.

Dose on Hardcopy output

If the area dose product meter is present, (Diamentor) con-
figure Yes. Otherwise configure No.

With present System MODULARIS the parameters for the Litho-
program have to be set again according the Service Instructions
LITHOSTAR MODULARIS.

NOTE

Содержание SIREMOBIL Iso-C

































































































































Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы:

Siemens SIREMOBIL Iso-C, Инструкция по эксплуатации, Страница: 91 / 128

Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы: