manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Инструкция по эксплуатации, Страница: 92 / 128

Поделиться
Скачать
Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 92

SIREMOBIL Iso-C

 

SPR2-230.061.01

Page 26 of 48

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

6 - 26

Replacing boards / replacing components

 

MEMOSKOP C-E 100

6

•

Replace the MEMOSKOP C-E 100.
The attachment screws are accessible on the underside of the storage device.

•

Check the software status of the MEMOSKOP. Download the system software to the 
MEMOSKOP if necessary.

•

Use the MEMOSKOP Service Software to import the language file.

•

Set the MEMOSKOP C-E 100 to the correct video frequency and configure it for the 
number of existing monitors.
Refer to chapter 5 "Configuring the video frequency " and "MEMOSKOP - Configuration 
for the number of existing monitors ."

•

Configure the following parameters in Technical Setup for MEMOSKOP:

Check the software status of the newly delivered MEMOSKOP. 
If the software status of the MEMOSKOP differs from that of the 
system, the system software status must be downloaded to the 
MEMOSKOP. 
The MEMOSKOP software status can be read out in the 2nd line 
of the User Setup. 
The first number describes the MEMOSKOP type. 
(2=CE; 3= CE-100/ C/ C & MOD; 4=C-SUB/ C-SUB & MOD).

The image storage MEMOSKOP C-E 100 is a new image storage 
that works only with the correct number of images. For this rea-
son, if the image storage was set to its default values 
(Menu "Diagnostics", "Load Factory Defaults"), the parameter 
"Maximum image numbers" must be set to 100 images.

Read and record the parameters for MEMOSKOP C-E 100 if you 
can select User setup. After replacing the MEMOSKOP, configure 
the MEMOSKOP C-E 100 according to the parameters noted.

Number of Monitors

Configure 1 for SIREMOBIL with 1 monitor.
Configure 2 for SIREMOBIL with 2 monitors.

Hardcopy 

Check whether 5000 is programmed in "4 Max Hardcopy 
time". If not, program this value.

Edge 1 coef set

Check whether 3 is programmed, If not, program this value.

Edge 2 coef set

Check whether 8 is programmed, If not, program this value.

Motion detection setup

Check whether the following are programmed "MD1: 
Threshold" 100 and for "MD2: Threshold" 120. If not, pro-
gram these values.

Date / Time format

Set the country-specific format.

Keyboard

Set to the keyboard layout being used.

Language

Set for language of the country.

Display of realtime clock

Configure Yes. Select No only upon customer request.

Display of rotated images

Configure Yes.

NOTE

NOTE

Содержание SIREMOBIL Iso-C

































































































































Отзывы:

Нет отзывов