manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Инструкция по эксплуатации, Страница: 66 / 128

Поделиться
Скачать
Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 66

SIREMOBIL Iso-C

 

SPR2-230.061.01

Page 30 of 30

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

5 - 30

Adjustments / Programs

 

After selecting the desired video frequency, press "Return". This configures the video fre-
quency you have just selected. After switching the SIREMOBIL OFF and ON again, the 
MEMOSKOP will start up at the correct video frequency.

MEMOSKOP, configuration for the number of existing monitors

5

When you replace the MEMOSKOP, it will be configured for 2 monitors. This configuration 
displays USER SETUP and TECHNICAL SETUP on the second monitor. 
Therefore, USER SETUP and TECHNICAL SETUP are not visible for SIREMOBIL Iso-C 
systems with only one monitor. 

Without installed MEMOSKOP keyboard:

•

Use the MEMOSKOP service program to modify the configuration.

With installed MEMOSKOP keyboard:

•

On the MEMOSKOP, reconnect the video cable from OUT 1 to OUT 2.

•

Press CTRL + T at the same time on the MEMOSKOP keyboard; TECHNICAL SETUP is 
called up and is now visible on the monitor.

•

Call up the menu "Number of monitors" by pressing the "3" key and subsequently the 
"RETURN" key on the MEMOSKOP keyboard.

•

With the -> and <- cursor keys, set the number to 1 monitor and press the "RETURN" 
key. The text display disappears on the monitor.

•

Press the "RETURN" key once more.

•

Reconnect the monitor to the OUT 1 video output. The text display is now visible on the 
monitor.

•

Exit TECHNICAL SETUP by pressing the "HOME" key on the MEMOSKOP keyboard.

MEMOSKOP, configuration and country-specific language (User Setup)

5

Start the MEMOSKOP service program and transfer the country-specific language to 
SIREMOBIL Iso-C via the service PC.

 

After completing the MEMOSKOP configuration, save the parame-
ters on a diskette. Exit the service program and switch the 
SIREMOBIL off and back on again.

NOTE

Содержание SIREMOBIL Iso-C

































































































































Отзывы:

Нет отзывов