Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 128

Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 37

5 - 1

Siemens AG

SPR2-230.061.01

Page 1 of 30

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

Adjustments / Programs

5

•

Connect the service PC to the serial interface of the SIREMOBIL Iso-C.

•

Start the service program.

•

Select the Diagnostic menu.

•

Select the Monitoring menu.

•

Select "KV offset adjustment in the "Group 1" Combo box.

•

Click on "Update Start".

•

After the "Start fluoro" message in the ACTIONS line, press the radiation release button
on the SIREMOBIL Iso-C SIREMOBIL Iso-C hand switch.

•

Continue to hold the radiation release button as long as the message "Continue fluoro" is
displayed in the ACTIONS line.

•

Release the radiation release button as soon as the message "Stop monitoring" appears
in the ACTIONS line.

•

Click on "Update Stop".

•

Perform the generator adjustment ( filament circuit learning program).

The kV offset adjustment has to be followed by the generator
adjustment (filament circuit learning program).
Always perform the kV offset adjustment prior to beginning the
generator adjustment.

X-ray radiation!
See Chapter 1, Safety Information.

Observe the need for radiation protection. Wear a lead apron.

After the "KV error break" message in the STATUS line, click on
"Update Stop". Wait approximately 10 seconds.
Click on "Update Start" again. After the "Start fluoro" message in
the ACTIONS line, press the radiation release button on the
SIREMOBIL Iso-C hand switch. Refer to the text which follows for
additional procedures.

NOTE

WARNING

NOTE

«
...
35
36
37
38
39
...
»

Содержание SIREMOBIL Iso-C

































































































































Отзывы:

Нет отзывов