Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 23

Страница: 23 / 128

Prerequisites

1 - 15

Siemens AG

SPR2-230.061.01

Page 15 of 18

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

Installing/ removing the C-arm covers

•

Remove the 4 mounting screws (Fig. 2). Hold the covers firmly while removing them.

•

Install them following the same procedure in the reverse order.

Monitor trolley

Removing the covers

•

Remove the upper back cover plate of the logbook compartment.

•

Remove the protective conductor.

•

Remove the lateral Allen screws from the lower back cover.

•

Remove the protective conductor from the cover.

Fig. 7

Risk of injuries on mechanical parts!
If not observed, slight to medium injuries, especially to the hands,
can occur.

Observe the notes concerning the C-arm carbon fiber structure.

Risk of injury!
Noncompliance can lead to light to medium injuries and/or
property damage.

The C-arm covers contain counterbalance weights and weigh
approx. 6 kg.
Hold the covers firmly when installing or removing them.

Before the C-arm cover will be loosened, the C-arm must be
moved to its middle orbital position.
If the C-arm covers are loosened, the C-arm may not be moved to
its orbital end positions (I.I. or SIREPHOS at the orbital end posi-
tion).

WARNING

CAUTION

Содержание SIREMOBIL Iso-C

































































































































Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы:

Siemens SIREMOBIL Iso-C, Инструкция по эксплуатации, Страница: 23 / 128

Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы: