Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 25

Страница: 25 / 128

Prerequisites

1 - 17

Siemens AG

SPR2-230.061.01

Page 17 of 18

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

I.I. service position

Moving the I.I. into the service position

•

Take the service screws from the kit supplied.

•

Move the C-arm into the vertical position, with the I.I. below and the SIREPHOS above.

•

Remove both attachment screws for the I.I. and replace them with the service screws.

•

Insert the service screws at least 5 turns into the threaded holes of the I.I.

•

Hold the I.I. firmly and turn the C-arm so that the I.I. is above and the SIREPHOS is be-
low (Angulation).

•

Hold the I.I. firmly and carefully remove it from the C-arm. Be careful not to damage the
cable.

Installing the I.I.

•

Move the C-arm into the vertical position with the I.I. below, the SIREPHOS above.

•

Holding the I.I. firmly, carefully lift it up. Be careful of the cable.

•

Holding the I.I. firmly, move the C-arm so that the Sirephos is above and the I.I. is below
(Angulation).

•

Carefully insert the I.I. into the C-arm. When doing this, be careful not to damage the ca-
ble.

•

Remove both the service screws from the threaded holes of the I.I. and reinstall both the
attachment screws.

Fig. 8

Risk of injuries on mechanical parts!
If not observed, slight to medium injuries, especially to the hands,
can occur.

Observe the notes concerning the C-arm carbon fiber structure.

WARNING

Содержание SIREMOBIL Iso-C

































































































































Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы:

Siemens SIREMOBIL Iso-C, Инструкция по эксплуатации, Страница: 25 / 128

Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы: