Siemens SENTRON ATC6300 Скачать руководство пользователя страница 134

Страница: 134 / 210

Parameterization

9.3 Parameters

3KC ATC6300 transfer control device

132

Manual, 03/2018, L1V30535632002A-01

P06 Pa-

rameter

Line 1

Designation on ATC

display

Description

Unit

Default

Range

P06.19

Generator start

delay

Delay of generator start after
failure of Line 1
– Delay in starting the generator if Line 1 fails to

meet set limits. If this value is set to OFF, the

starting cycle begins simultaneously with the

opening of the line contactor.

OFF

OFF / 1-6000

P06.20

Cooling time

Generator cooling time
– Maximum duration of the cooling cycle. Time

that elapses between the disconnection of load

from the generator and the engine actually

stopping.

120

OFF = The voltage measurement for Line 1 in the OFF mode is disabled.

ON = The voltage measurement in the OFF mode is enabled.

OFF+GLOB = The voltage measurement in the OFF mode is disabled but the relay

programmed for the global alarm function is either tripped or not, depending on whether the

line is present or missing.

ON+GLOB = The voltage measurement in the OFF mode is enabled and the relay

programmed for the global alarm function is either tripped or not, depending on whether the

line is present or missing.

9.3.7

P07 - Parameter Line 2

The default values for Line 1 and Line 2 are the same, only that they always refer to the

corresponding line.
For a detailed explanation of the parameters, please refer to chapter P06 - Line1 (Page 130).

P07 Pa-

rameter

Line 2

Designation on ATC

display

Description

Unit

Default Range

P07.01

Min voltage limit

Limit threshold for minimum trip voltage

70 - 100

P07.02

Min. voltage pick-up Limit threshold for resetting the minimum trip

voltage

70 - 100

P07.03

Min voltage delay

Delay time for minimum voltage

0 - 600

P07.04

Max voltage limit

Limit threshold for maximum trip voltage

115

100 - 130 /

OFF

P07.05

Max. voltage pick-

Limit threshold for resetting the maximum trip

voltage

110

100 - 130 /

OFF

P07.06

Max voltage delay

Delay for maximum voltage

0 - 600

P07.07

Presence delay

Presence delay (when Line 1 source not avail-

able)

1 - 6000

P07.08

Pres.del. Line 1 OK Presence delay (when Line 1 source available) s

1 - 6000

Содержание SENTRON ATC6300



















































































































































































































Результаты поиска

Содержание SENTRON ATC6300

Отзывы:

Siemens SENTRON ATC6300, Руководство пользователя, Страница: 134 / 210

Результаты поиска

Содержание SENTRON ATC6300

Отзывы: