manualshive.com logo in svg

Siemens SENTRON ATC6300, Руководство пользователя, Страница: 112 / 210

Поделиться
Скачать
Siemens SENTRON ATC6300 Скачать руководство пользователя страница 112

Operation 

 

8.3 Designation and description of the outputs 

 

3KC ATC6300 transfer control device 

110

 

Manual, 03/2018, L1V30535632002A-01 

Function 

Description 

Key AUT simulation 

Closing the input is the equivalent of pressing the 

AUT key. The operating mode is changed ac-

cordingly. 

Automatic test inhibition 

Inhibits the automation test. 

LED test 

Makes all the LEDs on the front panel flash. 

Close Breaker 1 (BRK 1) 

In the manual mode this function closes the 

Breaker 1. 

Open Breaker 1 (BRK 1) 

In the manual mode this function opens the 

Breaker 1. 

Toggle Breaker 1 (BRK 1) 

In the manual mode this function toggles the 

status of Breaker 1. 

Close Breaker 2 (BRK 2) 

In the manual mode this function closes the 

Breaker 2. 

Open Breaker 2 (BRK 2) 

In the manual mode this function opens the 

Breaker 2. 

Toggle Breaker 2 (BRK 2) 

In the manual mode this function toggles the 

status of Breaker 2. 

Auxiliary voltage ready 

If this NC contact is open, alarm A18 is triggered. 

Revision 

If enabled, this function causes the following 

reactions during revision of the system:  

•

 

switch to OFF mode 

•

 

disabling of feedback alarms A03-A04 

•

 

enabling of any undervoltage release 

8.3

 

Designation and description of the outputs 

8.3.1

 

Digital outputs OUTx 

The ATC6300 has 7 permanently integrated digital outputs which are designated as OUTx. 

 

Designation 

Description 

Mounted on the device  Maximum number with 

expansion modules 

OUTx 

Digital output 

1 - 7 

8 - 15 

The function of the integrated digital outputs can be freely parameterized by the user:  

Содержание SENTRON ATC6300



















































































































































































































Отзывы:

Нет отзывов