manualshive.com logo in svg

Siemens SENTRON ATC6300, Руководство пользователя, Страница: 54 / 210

Поделиться
Скачать
Siemens SENTRON ATC6300 Скачать руководство пользователя страница 54

Functions 

 

5.1 Basic functions 

 

3KC ATC6300 transfer control device 

52

 

Manual, 03/2018, L1V30535632002A-01 

5.1.8

 

Simulation of priority line failure 

The ATC6300 offers the possibility of simulating a power failure. This enables the system to 

be tested.  
This simulation can be performed in two ways:  

●

 

Via the command menu, using the command C16 

●

 

Through a digital input with the function C16 

The simulation involves considering a two-minute absence of the priority line, even if it is 

actually present. During this time the message SIMUL xxx appears on the main page with a 

countdown of the simulation time: 

 

The simulation will cause the start of the generator (if present) and a load transfer exactly as 

in the automatic cycle.  

Stopping the simulation 
The simulation can be stopped at any time by pressing the OFF key, thereby placing the 

device in the OFF mode.  

 

 

Note 
If the simulation is performed through the command menu, it must be started from the OFF 

mode. Only in the OFF mode is it possible to execute commands (see chapter Command 

menu (Page 53)). 
After selecting and confirming the command C.16 the command menu is exited. The device 

switches automatically to the automatic mode and starts the simulation.  

 

Содержание SENTRON ATC6300



















































































































































































































Отзывы:

Нет отзывов