manualshive.com logo in svg

Siemens SENTRON ATC6300, Руководство пользователя, Страница: 8 / 210

Поделиться
Скачать
Siemens SENTRON ATC6300 Скачать руководство пользователя страница 8

Table of contents 

 

 

 

3KC ATC6300 transfer control device 

6

 

Manual, 03/2018, L1V30535632002A-01 

11 

MODBUS communication .................................................................................................................... 147 
11.1 

General information on MODBUS........................................................................................ 147 

11.2 

MODBUS RTU protocol ....................................................................................................... 148 

11.3 

MODBUS ASCII protocol ..................................................................................................... 149 

11.4 

MODBUS functions .............................................................................................................. 151 

11.5 

Password entry by means of MODBUS ............................................................................... 156 

11.6 

Data library ........................................................................................................................... 157 

11.6.1 

Measured values (use with MODBUS function 03 and 04) ................................................. 157 

11.6.2 

Status bits (use with MODBUS function 03 and 04) ............................................................ 159 

11.6.3 

Commands (use with MODBUS function 06) ...................................................................... 164 

11.6.4 

Status of the ATC (use with MODBUS function 03 and 04) ................................................ 166 

11.6.5 

Real-time clock (use with MODBUS function 04 and 06) .................................................... 167 

11.7 

Reading the event log .......................................................................................................... 167 

11.8 

Reading parameters by means of MODBUS ....................................................................... 170 

11.9 

Changing parameters by means of MODBUS ..................................................................... 170 

12 

Accessories ......................................................................................................................................... 175 
12.1 

Expansion modules .............................................................................................................. 175 

12.1.1 

Expansion module 4DI - 3KC9000-8TL60 ........................................................................... 176 

12.1.1.1 

Technical specifications ....................................................................................................... 178 

12.1.2 

Expansion module 4DO - 3KC9000-8TL61 ......................................................................... 180 

12.1.2.1 

Technical specifications ....................................................................................................... 181 

12.1.3 

Expansion module 2DI 2DO - 3KC9000-8TL62 ................................................................... 182 

12.1.3.1 

Technical specifications ....................................................................................................... 184 

12.1.4 

Expansion module 2DO - 3KC9000-8TL63 ......................................................................... 185 

12.1.4.1 

Technical specifications ....................................................................................................... 186 

12.1.5 

Expansion module 2DI 2DO - 3KC9000-8TL64 ................................................................... 188 

12.1.5.1 

Expansion module 2DI 2DO - 3KC9000-8TL64 ................................................................... 188 

12.1.5.2 

Technical specifications ....................................................................................................... 189 

12.1.6 

Expansion module RS485 - 3KC9000-8TL74 ...................................................................... 190 

12.1.6.1 

Technical specifications ....................................................................................................... 191 

12.1.7 

Expansion module Ethernet - 3KC9000-8TL75 ................................................................... 192 

12.1.7.1 

Technical specifications ....................................................................................................... 192 

12.2 

Cover frame - 3KC9000-8TL68 ............................................................................................ 193 

12.3 

USB front interface - 3KC9000-8TL73 ................................................................................. 194 

13 

Technical specifications ....................................................................................................................... 195 

14 

Dimension drawings ............................................................................................................................. 199 

A 

List of abbreviations ............................................................................................................................. 201 
A.1 

List of abbreviations ............................................................................................................. 201 

 

Index ................................................................................................................................................... 203 

Содержание SENTRON ATC6300



















































































































































































































Отзывы:

Нет отзывов