Siemens SENTRON ATC6300 Скачать руководство пользователя страница 128

Страница: 128 / 210

Parameterization

9.3 Parameters

3KC ATC6300 transfer control device

126

Manual, 03/2018, L1V30535632002A-01

P05
Changeo-

ver

Designation on ATC

display

Description

Unit

Default

Range

P05.07

Switching devices

Type of switching device
– This parameter specifies whether the pro-

grammable Open / Close outputs must be con-

tinuously active (application with contactors or

with switching devices without feedback) or

operating in the pulse mode, i.e. enabled until

the switching device is located in the correct

position. If the pulse mode is selected, the

command is extended for a certain time (see

P5.08 and P5.09), even after the position has

been reached.

Brk. Pul. Brk. Pul.

Brk. Con.
Chg. Pul.
Chg. Con.
Contactors

P05.08

Opening pulse dur. Opening pulse duration

– Minimum duration of an opening command

pulse. In the application using circuit breakers

with motor operators, a sufficiently long time

must be set in order to enable the complete

charging of the springs. This time is also taken

into consideration when operating in the contin-

uous signal mode.

1-600

P05.09

Closing pulse dur.

Closing pulse duration
– Pulse duration of the closing pulse.

1-600

P05.10

Cont. command in

OFF

Continuous command in the RESET / OFF

mode
– This specifies the behavior of the open-

ing/closing command outputs in the continuous

signal mode, if the ATC6300 is in the

RESET / OFF mode. Used in applications with

contactors.
OFF – Opens the command outputs
NOC – Leaves the outputs unchanged

NOC

OFF
NOC

P05.11

Load no powered

tim.

Maximum time during which the load has no

power - response delay for Alarm A07
– If both power supplies are simultaneously

unavailable for longer than the time set in

P5.11, alarm A07 is triggered.

OFF/1…3600

P05.12

Inh. aut. ret. pr. line Inhibits the automatic return to the priority line

– If this parameter is enabled, the supply is not

automatically switched back from the secondary

line to the priority line when it becomes availa-

ble again. Instead, it must be switched back

manually.
OFF – Disabled
ON – Lock enabled

OFF

OFF/ON

P05.13

EJP mode

EJP mode
– Normal = Standard mode in the AUT mode.

Normal

Normal
EJP

EJP-T

SCR

Содержание SENTRON ATC6300



















































































































































































































Результаты поиска

Содержание SENTRON ATC6300

Отзывы:

Siemens SENTRON ATC6300, Руководство пользователя, Страница: 128 / 210

Результаты поиска

Содержание SENTRON ATC6300

Отзывы: