Siemens SENTRON ATC6300 Скачать руководство пользователя страница 123

Страница: 123 / 210

Parameterization

9.3 Parameters

3KC ATC6300 transfer control device
Manual, 03/2018, L1V30535632002A-01

121

9.3.1

P01 - Settings

P01
Settings

Designation on ATC

display

Description

Unit

Default

Range

P01.01

Language

Sets the language
– This parameter is used for setting the lan-

guage of the user interface.

English

English
Italiano
Francais
Espanol
Deutsch

P01.02

Clock setting PWR

Setting of the real-time clock when switching on

the power supply
– This parameter determines whether the real-

time clock is to be reset or not after each

startup.

OFF

OFF-ON

P01.03

Op. mode at power

Operating mode after switching on
– This parameter determines which mode the

ATC6300 enters after switching on. It can either

be always switched on in the operating mode

OFF, or in the last operating mode used before

the device was switched off.

Previous OFF mode

P01.04

Display contrast

Display contrast
– This can be used to adjust the contrast of the

LCD display.

0-100

P01.05

High backlight level High backlight level

– This parameter sets the bright LCD backlight-

ing.

100

0-100

P01.06

backlight delay

Low backlight level
– This parameter sets the low LCD backlighting.

0-50

P01.07

Load no backlight

delay

Delay low LCD backlighting
– This allows you to set a delay time, after

which the ATC6300 switches to low backlight-

ing.

180

5-600

P01.08

ret. page return

Default page return
– This parameter controls whether the device

switches to a default page defined under

P01.09 if no key is pressed within a specific

time. If this parameter is set to OFF, the

ATC6300 always remains on the last page to

be opened.

300

OFF / 10-600

P01.09

Default page

Selection of the default page
– This parameter is used to select a new default

page from the existing display pages of the

ATC6300. In connection with P01.08, a switch

is made to this page after a certain time.

VL-L

(List with dis-

play pages)

P01.10

Transfer Switch ID

Plant identifier
– You can enter any alphanumeric description

of the plant here.

SIEMEN

ATC630

String 20 chr.

Содержание SENTRON ATC6300



















































































































































































































Результаты поиска

Содержание SENTRON ATC6300

Отзывы:

Siemens SENTRON ATC6300, Руководство пользователя, Страница: 123 / 210

Результаты поиска

Содержание SENTRON ATC6300

Отзывы: