Siemens SENTRON ATC6300 Скачать руководство пользователя страница 23

Страница: 23 / 210

Product description

4.1 Product description

3KC ATC6300 transfer control device
Manual, 03/2018, L1V30535632002A-01

Keys

No.

Key

Function

③

Key

▲

•

Pressing this key switches between menu pages. Within the menus, it is used to switch between

the parameters.

④

MAN / +

•

Pressing the MAN / + key for at least 0.5 seconds selects the Manual operating mode.

•

If the MAN / + key is pressed within the individual menus, the parameters can be increased.

⑦

Key

▼

•

Pressing this key switches between menu pages. Within the menus, it is used to switch between

the parameters.

⑧

AUT /

✓

•

Pressing the

AUT / ✓

key for more than 0.5 seconds selects the automatic mode.

•

Pressing the

AUT / ✓

key also confirms any settings that have been made.

⑪

OFF / -

•

Pressing the OFF / - key for more than 0.5 seconds selects the OFF mode.

•

If the OFF / - key is pressed within the individual menus, the parameters can be reduced.

Simultaneously pressing the

▲

and

▼

keys returns you to the main menu. You can find more

information in chapter Menu navigation (Page 22).

Interface

A 3KC9000-8TL73 USB front interface can be attached to interface 5. This enables the

ATC6300 transfer control device to be parameterized from the front using powerconfig

(Version 3.10 or higher).
Further information on the 3KC9000-8TL73 USB front interface can be found in chapter

Parameterization via the front interface (Page 119) or in chapter USB front interface -

3KC9000-8TL73 (Page 194)

QR code

The QR code 6 contains information that refers to the Industry Mall page of the ATC6300

transfer control device, where further information is available, e.g. operating instructions and

certificates.

Содержание SENTRON ATC6300



















































































































































































































Результаты поиска

Содержание SENTRON ATC6300

Отзывы:

Siemens SENTRON ATC6300, Руководство пользователя, Страница: 23 / 210

Результаты поиска

Содержание SENTRON ATC6300

Отзывы: