Siemens SENTRON ATC6300 Скачать руководство пользователя страница 132

Страница: 132 / 210

Parameterization

9.3 Parameters

3KC ATC6300 transfer control device

130

Manual, 03/2018, L1V30535632002A-01

9.3.6

P06 - Parameter Line 1

The default values for Line 1 and Line 2 are the same, only that they always refer to the

corresponding line.

P06 Pa-

rameter

Line 1

Designation on ATC

display

Description

Unit

Default

Range

P06.01

Min voltage limit

Limit threshold for minimum trip voltage
– The first two parameters specify the minimum

voltage threshold limit and the related hystere-

sis upon restoration of power. P6.02 cannot be

set to a lower value than P6.01. P6.03 defines

the intervention delay of this safety mechanism

70-100

P06.02

Min. voltage pick-up Limit threshold for resetting the minimum trip

voltage
- see Parameter 06.01

70-100

P06.03

Min voltage delay

Delay time for minimum voltage
- see Parameter 06.01

0-600

P06.04

Max voltage limit

Limit threshold for maximum trip voltage
– The first two parameters specify the maxi-

mum voltage threshold limit and the related

hysteresis upon restoration of power. P6.05

cannot be set to a higher value than P6.04. If

P6.04 is set to OFF, the
maximum voltage measurement is disabled.

P6.06 specifies the maximum voltage interven-

tion delay.

115

100-130 / OFF

P06.05

Max. voltage pick-

Limit threshold for resetting the maximum trip

voltage
- see Parameter 06.04

110

100-130 / OFF

P06.06

Max voltage delay

Delay for maximum voltage
- see Parameter 06.04

0-600

P06.07

Presence delay

Presence delay (when Line 2 source not avail-

able)
– Used if the energy source of Line 2 is not

available.
This defines after what time the ATC considers

the line to be stable (if within the limit thresh-

olds). During this time the LED Line 1 signals

availability.
Normally this time is shorter than P6.08, as the

load is non energized, and voltage needs to be

supplied urgently.

1-6000

Содержание SENTRON ATC6300



















































































































































































































Результаты поиска

Содержание SENTRON ATC6300

Отзывы:

Siemens SENTRON ATC6300, Руководство пользователя, Страница: 132 / 210

Результаты поиска

Содержание SENTRON ATC6300

Отзывы: