Siemens SCALANCE X204RNA EEC Скачать руководство пользователя страница 97

Страница: 97 / 132

Functional description and configuration using Web based Management

7.8 The Switch menu

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)
Operating Instructions, , C79000-G8976-C294-03

Figure 7-39 Packet Type Statistic Graphic

With the check box in the "Packet Type" column, you decide the content of the graphic. The

value in the "Packets" column in the graphic is only displayed for a certain packet type if the

appropriate check box is selected. The "Percentage" column shows the packets of a certain

type as a percentage of the total packets for this port. When the percentage is calculated,

packet types are included only if their check boxes are selected.
With the "Previous Port" and "Next Port" buttons, you can change to the display of the

previous or next port.

7.8.8

Packet Error Statistic

Errors in received packets

The "Packet Error Statistics" page shows how many bad frames were received per port. The

following error types are distinguished:
●

Bad Frames

Total number of bad received frames.

●

CRC

Number of frames whose content did not match the CRC checksum.

●

Undersize

Number of frames with a length less than 64 bytes.

Содержание SCALANCE X204RNA EEC





































































































































Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE X204RNA EEC, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды