Siemens SCALANCE X204RNA EEC Скачать руководство пользователя страница 127

Страница: 127 / 132

Glossary

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)
Operating Instructions, , C79000-G8976-C294-03

127

Single mode

In single mode transmission, (and monomode transmission) the pulse is transmitted by a

straight mode (wave). Attenuation is mainly caused by physical absorption and dispersion as

well as by mechanical bending. The amount of attenuation depends, among other things, on

the wavelength of the input light. The single mode fiber typically has a core diameter of 5 to 9

µm. The outer diameter is, however, once again 125 µm (compare multimode). The smaller

core diameter degrades the pulse edges less than multimode transmission and allows

greater transmission distances.

SNMP

Simple Network Management Protocol. Standardized protocol for transporting network

management information.

SNTP

Simple Network Time Protocol
Protocol for time synchronization over networks.

SSH

Secure Shell. This allows an interactive connection to be established to another device in the

LAN or on the Internet. Otherwise, the functionality corresponds to that of Telnet.

SSL

Secure Socket Layer. This protocol allows encrypted exchange of data with a server. There

is also secure authentication of the server. For communication with a server over SSL, the

server must have a certificate and a corresponding private key.

Store and forward

An entire frame is received, its validity checked (checksum, length etc.) and then buffered.

Invalid frames are discarded, in other words, a frame is forwarded only when it is error-free.

TELNET

With this protocol, an interactive connection can be established to another device in the LAN

or on the Internet. The user then has the same options as when directly connected to this

device with a terminal.

Twisted Pair

Содержание SCALANCE X204RNA EEC





































































































































Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Бренды по названию

Популярные бренды

Siemens SCALANCE X204RNA EEC, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Бренды по названию

Популярные бренды