Siemens SCALANCE X204RNA EEC Скачать руководство пользователя страница 91

Страница: 91 / 132

Functional description and configuration using Web based Management

7.8 The Switch menu

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)
Operating Instructions, , C79000-G8976-C294-03

Active

Indicates whether or not the port is turned on (true). Data traffic is possible only over an

enabled port.

Note
With the SCALANCE X-200RNA, the ports cannot be turned off.

Link

Shows the connection status to the network. The available options are as follows:
●

The port has a valid link to the network, a link integrity signal is being received.

●

Down

The link is down, for example because the connected device is turned off.

7.8.4

Switch Forwarding Database

Display of the Switch Forwarding Database

The "Switch Forwarding Database" screen appears if you click the "FDB" folder icon.
The screen shows the dynamically learnt MAC addresses in the FDB table for all ports. In

addition to this, to allow PRP diagnostics, the screen also shows whether the displayed MAC

addresses are listed in the duplicate filter or in the proxy node table.

Содержание SCALANCE X204RNA EEC





































































































































Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE X204RNA EEC, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды