Siemens SCALANCE X204RNA EEC Скачать руководство пользователя страница 81

Страница: 81 / 132

Functional description and configuration using Web based Management

7.7 The Agent menu

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)
Operating Instructions, , C79000-G8976-C294-03

Figure 7-28 Agent Event Configuration with the SCALANCE X204 RNA

You can configure the reaction of the SCALANCE X-200RNA to the following events:
Cold / Warm Start

The SCALANCE X-200RNA was turned on or restarted by the user.
Link Change

A port has failed or data traffic is being handled again over a port that had previously failed.
Authentication Failure

There was an SNMP access with a bad password or inadequate access rights.
Power Error (SCALANCE X204RNA only)

This event occurs only when the power supply line 1 and line 2 are monitored. It indicates

that there was a change to line 1 or line 2.
Fault State Change

The fault status has changed. The fault status can relate to the activated port monitoring, the

response of the signaling contact or the power supply monitoring.
Redundancy Event

There are two situations that are signaled as a redundancy error.

Содержание SCALANCE X204RNA EEC





































































































































Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE X204RNA EEC, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды