manualshive.com logo in svg

Siemens SCALANCE X204RNA EEC, Руководство по эксплуатации

Поделиться
Скачать
Siemens SCALANCE X204RNA EEC Скачать руководство пользователя страница 54

Functional description and configuration using Web based Management 

 

7.5 The System menu 

 

SCALANCE X204RNA  SCALANCE X204RNA EEC     (PRP) 

54

 

Operating Instructions,  , C79000-G8976-C294-03 

How to download data using HTTP 

1.

 

In the relevant text box, enter a name and directory path for the file from which you want 

to take the data. 

2.

 

Start the download of the relevant file by clicking one of the buttons "Load Configuration 

and Restart", "Load Firmware and Restart" or "Load FPGA File and Restart", "Load 

Private Key" or "Load Certificate and Restart". Following the download, there is an 

automatic restart except with "Load Private Key" and the device starts up with the new 

data. Note the following: 

 

 

Note 
If a firmware version is loaded that is older than the current version, it is possible that the 

current parameter record cannot be adopted. In this case the current IP address is 

deleted and access using WBM, CLI or SNMP is no longer possible. This means that 

after downloading the firmware and restarting the device, the IP address needs to be 

assigned again with the Primary Setup Tool and the required parameters set again. 

 

 

Note 
If newer firmware and a newer FPGA version required on the device, it is advisable to 

download the FPGA and then the firmware following the restart. 

How to save data using HTTP 

1.

 

Start the save function by clicking either the "Save Configuration" or "Save Private MIB" 

button. 

2.

 

You will be prompted to select a storage location and a name for the file or to accept the 

proposed file name. 

Reusing configuration data 

Saving and reading in configuration data reduces the effort if several SCALANCE X-200RNA 

devices have the same configuration and when IP addresses are obtained over DHCP. 
Save the configuration data on your computer after you have configured a SCALANCE X-

200RNA. 
Download this file to all other SCALANCE X-200RNA devices you want to configure.  
If individual settings are necessary for specific devices, these must be made online. 
The stored configuration data is coded and, as a result, these files cannot be edited with a 

text editor. 

Содержание SCALANCE X204RNA EEC





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды