Siemens SCALANCE X204RNA EEC Скачать руководство пользователя страница 30

Страница: 30 / 132

Product characteristics

4.8 Displays

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)

Operating Instructions, , C79000-G8976-C294-03

Power supply L is connected

Power supply L is not connected or the supply voltage is too low.

4.8.3

Port status indication

Port status indicator (green/yellow LEDs)

The LEDs signal the following port statuses of the SCALANCE X-200RNA.
The status of interfaces is indicated by two-color LEDs:

Device type SCALANCE

Number of LEDs

LED lit green

LED lit yellow

LED flashes yellow

2 port LEDs

2, 3

X204RNA

2 PRP port LEDs

2, 3

2 port LEDs

2, 3

X204RNA EEX

2 PRP port LEDs

2, 3

TP link exists, no data reception.

TP link, data received at TP port.

Device startup, the LED is lit for approx. 6 seconds.

Setting or display of the fault mask.

4.8.4

LED displays during startup

When a device starts up, the following displays light up in the order shown:
1.

Power LEDs (green) light up immediately after turning on the power.

Port LEDs go off, the red error LED is lit for approx. 10 seconds.

Following startup, the correct link status is indicated by the port LEDs after approximately

5 seconds.

The SCALANCE X-200RNA is now ready for operation.

Содержание SCALANCE X204RNA EEC





































































































































Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE X204RNA EEC, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды