Siemens SCALANCE X204RNA EEC Скачать руководство пользователя страница 7

Страница: 7 / 132

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)
Operating Instructions, , C79000-G8976-C294-03

Introduction

1.1

Introduction

Overview of SCALANCE X-200RNA

The SCALANCE X-200RNA product family is part of the SCALANCE X product family.

Below, you will find a brief overview of this product family.
The SCALANCE X family comprises various product lines that complement each other and

that are carefully tuned to specific automation tasks.

What is possible?

The devices of the SCALANCE X-200RNA product line allow the cost-effective setup of

Industrial Ethernet structures with Parallel Redundancy Protocol functionality.

Purpose of the Operating Instructions

These Operating Instructions support you when commissioning networks with the devices of

the product line SCALANCE X200RNA.

Validity of the Operating Instructions

These Operating Instructions are valid for the following devices of the SCALANCE X-

200RNA product line

SIMATIC NET SCALANCE X204RNA

6GK5204-0BA00-2KB2

SIMATIC NET SCALANCE X204RNA EEC

6GK5204-0BS00-3LA3

Names of the devices in these operating instructions

The descriptions in these operating instructions always apply to the devices of the

SCALANCE X-200RNA product line listed under "Validity of the Operating Instructions" in

this document unless the description relates to a specific device of the product line.

Further documentation

The "SIMATIC NET Industrial Ethernet Twisted Pair and Fiber Optic Networks" manual

contains additional information on other SIMATIC NET products that you can operate along

with the devices of the SCALANCE X-200 product line in an Industrial Ethernet network.

Содержание SCALANCE X204RNA EEC





































































































































Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE X204RNA EEC, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды