Siemens SCALANCE X204RNA EEC Скачать руководство пользователя страница 109

Страница: 109 / 132

Technical data

9.1 Technical specifications

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)
Operating Instructions, , C79000-G8976-C294-03

109

Table 9- 6

Permitted cable lengths (fiber-optic)

SFP modules only for
SCALANCE X204RNA EEC

0 - 3,000 m
Glass FO cable
62.5/125 µm multimode
glass fiber

0 - 26,000 m
Glass FO cable 10/125 µm
single mode fiber

0 - 70,000 m
Glass FO cable 10/125 µm
single mode fiber

SFP module SFP991-1

SFP module SFP991-1LD

SFP module SFP991-1LH+

Table 9- 7

Degree of protection and MTBF

Device type
SCALANCE

Degree of protection

MTBF

X204RNA

IP20

92.45 years

X204RNA EEC

IP20

67.64 years

Table 9- 8

Switching properties

Device type
SCALANCE

Max. number of
learnable addresses

Aging time

Switching technique

Latency

X204RNA

1023

30 s

Store and forward

15 - 135 µs

X204RNA EEC

1023

30 s

Store and forward

15 - 135 µs

Table 9- 9

Permitted ambient conditions

Device type
SCALANCE

Operating temperature

Storage/transportatio
n temperature

Relative humidity
in operation

Operating altitude at max. xx°C
ambient temperature

X204RNA

-40 °C t60 °C

-40 °C t70

°C

‹ 95 %
(no condensation)

2000 m at max. 56 °C
3000 m at max. 50 °C

X204RNA EEC

-40 °C t70 °C
(up to +85 °C / max. 16

-40 °C t70

°C

‹ 95 %
(no condensation)

2000 m at max. 56 °C
3000 m at max. 50 °C

Note
Note the orientation of the installed SCALANCE X204RNA and X204RNA EEC
If a SCALANCE X204RNA or X204RNA EEC are mounted on a vertical rail, an ambient

temperature of m40 °C is permitted.

Содержание SCALANCE X204RNA EEC





































































































































Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE X204RNA EEC, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды