Siemens SCALANCE X204RNA EEC Скачать руководство пользователя страница 29

Страница: 29 / 132

Product characteristics

4.8 Displays

SCALANCE X204RNA SCALANCE X204RNA EEC (PRP)
Operating Instructions, , C79000-G8976-C294-03

4.8

Displays

4.8.1

Fault indicator (yellow/red LED)

If the LED is lit red, a SCALANCE X-200RNA has detected an error/fault.
At the same time, the signaling contact opens assuming that the response of the signaling

contact has not been configured differently.
The LED signals that the SCALANCE X-200RNA can adopt the following statuses:

Device type SCALANCE

LED lit red

LED lit yellow

LED not lit

X204RNA

1, 2, 3, 4, 5

X204RNA EEC

1, 3, 4, 5

Link down event on a monitored port.

Failure of one of the two redundant power supplies.

C-PLUG error

Device startup, the LED is lit for approx. 20 seconds.

Internal error.

A redundancy error was detected.

No problem has been detected by the SCALANCE X-200RNA.

4.8.2

Power display

The LEDs signal the following statuses of the SCALANCE X-200RNA.
The status of the power supply is indicated by a green LED:

Device type SCALANCE

LED lit green

LED lit yellow

LED not lit

X204RNA

X204RNA EEC

Both L power supplies are connected (redundant supply).

One L power supply is connected (non-redundant supply).

Power supply L1 and L2 are not connected or supply voltages are <14 V.

Содержание SCALANCE X204RNA EEC





































































































































Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE X204RNA EEC, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X204RNA EEC

Отзывы:

Похожие инструкции для SCALANCE X204RNA EEC

Бренды по названию

Популярные бренды