Siemens LITHOSTAR Multiline SP Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 54

background image

LITHOSTAR Multiline

RXL2-120.815.01

Page 10 of 18

Siemens AG

System manual

Rev. 02

02.05

CS PS 24

Medical Solutions

6 - 10

Checking the Dose Rate

•

If the dose rate is acceptable:

- Connect the service PC to the Multiline.
- Call up "Parameter" in the Adjustment menu.
- Click on "Get from Unit."
- Select the parameter :" am 7 TV-Iris" in the Parameter Groups menu.
- Transfer the value appearing at "FLUORO Zoom 0" to "FLUORO Zoom 1" and

"FLUORO Zoom 2".

Dose rate setting for ZOOM 3:

- The dose rate for FLUORO Zoom 3 must be set separately.

•

Note the factor for the chamber.
If you are using the Dali -/Nomex-chamber for the measurement, the dose rate value
must be increased by 6%.

•

Leave the dose measurement chamber attached to the I.I.

•

Connect the service PC to the Multiline and login.

•

Release fluoro.

•

Call up "Parameter" in the Adjustment menu.

•

Click on "Get from Unit".

•

Select the parameter : "am 7 TV-Iris" in the Parameter Groups menu.

•

Select the "FLUORO" " Zoom 3" parameter.

•

In the "Value Actual" field, reduce or increase the zoom value.
- If the dose is too high, increase the value

•

After completing the change, click "Set Value".
The changed value is marked in the parameters window.
(It is not yet transferred to the unit.)

•

Click on "Put to Unit". The message "Component ... to continue" appears.

•

Click "OK" after the automatic reset.

•

Switch fluoro on if the dose value is acceptable.

•

End the adjustment, otherwise repeat it.

Zoom3 is not set like Zoom 0. The videomed DI service software
does not perform a nominal-actual comparison.

33 cm I.I. Zoom 3

Multiline without grid:

430 nGy/s

49

µ

R/s

Multiline with grid:

670 nGy/s

77

µ

R/s

After each Reset of the Multiline, the antiisowatt curve must be
selected on the operating PC.

NOTICE

NOTE

«
...
38
39
40
41
42
...
»

Содержание LITHOSTAR Multiline SP























































Отзывы:

Нет отзывов

Похожие инструкции для LITHOSTAR Multiline SP

Бренд: Raymarine Страницы: 55

Бренд: Halyard Страницы: 4

Underwater Light Show & Fountain

Бренд: GAME Страницы: 2

Бренд: Salvis Страницы: 40

Бренд: IDEAL Страницы: 2

Ettan IPGphor 3

Бренд: GE Страницы: 64

Бренд: GE Страницы: 56

Бренд: GE Страницы: 132

Бренд: GE Страницы: 16

Бренд: GE Страницы: 474

Бренд: TC Electronic Страницы: 4

Бренд: TC Electronic Страницы: 6

Бренд: TC-Helicon Страницы: 12

Бренд: TC Electronic Страницы: 76

Бренд: Ultraflex Страницы: 48

Бренд: Yamaha Страницы: 31

Бренд: YASKAWA Страницы: 1166

Бренд: Agilent Technologies Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды