Siemens LITHOSTAR Multiline SP Скачать руководство пользователя страница 37

Страница: 37 / 54

Checking the Dose Rate

6 - 7

Siemens AG

RXL2-120.815.01

Page 7 of 18

LITHOSTAR Multiline

Medical Solutions

Rev. 02

02.05

CS PS 24

System manual

•

Record the measurement value (approx. 3.1 mA).

•

Exit the dose rate adjustment field with "OK" after the dose rate has been reached.

•

Enter "150 mV" in the B-Signal value field.

•

Confirm the B-signal value with OK.

•

Click "Fluoroscopy on" in the CCD Brightness Adjust window.

•

Ignore the numerical value and click "Fluoroscopy off".

•

Click Cancel.

•

Confirm the message "Iris setting ..." with OK.

•

Select Dose rate in the Adjustment menu.
The message

IImaximum ...

appears.

•

Select the I.I. full field of view and open the collimator until it matches the size of the
measurement chamber.

•

Confirm the message

IImaximum ...

with OK.

•

Click Fluoroscopy on.

•

Change the mA value so that the dose rate desired appears on the dosimeter.

•

Record the measurement value (approx. 3.1 mA).

•

Enter "300 mV" in the B-Signal value field.

•

Click OK.

•

Wait for the data to be transferred to the generator (this may take some time).

•

Click "Fluoroscopy on" in the CCD Brightness Adjust field if the value 0 + 1 is not
reached.

•

Exit the XCS software.
- Switch fluoroscopy

- Read out the nominal/actual value. Record values and mathematical signs if there are

deviations (refer to RXL2-120.034.02..).

- Switch fluoroscopy

OFF

- Connect the service PC to the Multiline if there are deviations.
- Call up "Parameter" in the Adjustment menu.
- Click Get from Unit.
- Select the parameter: am 7 TV-Iris in "Parameter Groups".
- Select "TV-Iris format" under Parameter.

Dose rate

B-Signal

Multiline without grid:

261 nGy/s

R/s

300 mV

Multiline with grid:

433 nGy/s

R/s

300 mV

Dose rate

B-Signal

Multiline without grid:

261 nGy/s

R/s

300 mV

Multiline with grid:

433 nGy/s

R/s

300 mV

Содержание LITHOSTAR Multiline SP























































Результаты поиска

Содержание LITHOSTAR Multiline SP

Отзывы:

Похожие инструкции для LITHOSTAR Multiline SP

Бренды по названию

Популярные бренды

Siemens LITHOSTAR Multiline SP, Инструкции по запуску

Результаты поиска

Содержание LITHOSTAR Multiline SP

Отзывы:

Похожие инструкции для LITHOSTAR Multiline SP

Бренды по названию

Популярные бренды