Siemens Drager medical Carina Скачать руководство пользователя страница 89

Страница: 89 / 144

Instructions for Use Carina SW 3.n

Configuration

The configuration menu shows the configurable
functions and parameters:
– Service for system and contact information and

log book

– Volume – adjustable from 1 to 5
– Tone – default tone or Dräger tone can be

selected

– Screen – adjustable for displaying curves or val-

ues

– Set value – for selecting measured values to

display value 1 and value 2

– Method – for setting mask or tube ventilation

(only possible in standby mode)

– LPO – for setting LPO oxygen supply
– Ti / I:E – for selecting the setting used for Ti or

I:E ratio

– Night – for switching on the screen in night time

mode

To set:

Press the appropriate button for function or
parameter.

Select the value using the rotary knob and con-
firm.

Service menu

The »

Service

« menu is password-protected.

The password can only be changed by
DrägerService. If you have forgotten the password,
it can be reconstructed by DrägerService.

Opening the Service menu
1

Press the »

Service

« button. Carina prompts

you to enter the password.

Press buttons 1, 2, 3, 4 and 5 one after the
other.

Press the rotary knob to confirm the password.

540

541

542

540

547

Содержание Drager medical Carina

















































































































































Результаты поиска

Содержание Drager medical Carina

Отзывы:

Siemens Drager medical Carina, Инструкция по эксплуатации, Страница: 89 / 144

Результаты поиска

Содержание Drager medical Carina

Отзывы: