Siemens Drager medical Carina Скачать руководство пользователя страница 48

Страница: 48 / 144

Preparation

Instructions for Use Carina SW 3.n

External battery connection
1

Insert the DC connector in the Carina.

Connect the external battery. Refer to the
Instructions for Use of the external battery.

The external battery is not charged from the Carina
mains supply!

External battery for 3rd party connection

12 to 24 V DC (–10 % to +30 %); 6.3 to 3.2 A
Ensure that the battery is connected with correct
polarity!

Insert the plug.

Connect a microfuse (6.3 A slow blow) to the
external battery.

Connect the cable to the microfuse.
The LED

flashes or lights up according to

the charge of the internal battery.

The external battery is not charged from the Carina
mains supply!

WARNING
Mains-powered equipment must not be con-
nected to the connection for an external bat-
tery. Risk of electric shock or equipment
damage.

CAUTION

Avoid high resistance in conjunction with the
external battery by keeping the electrical connec-
tors clean at all times to avoid insufficient power
being delivered to the device.

CAUTION

The external battery must always have sufficient
capacity as directed in the Instructions for Use for
the external battery.

092

External battery

- +

Содержание Drager medical Carina

















































































































































Результаты поиска

Содержание Drager medical Carina

Отзывы:

Siemens Drager medical Carina, Инструкция по эксплуатации, Страница: 48 / 144

Результаты поиска

Содержание Drager medical Carina

Отзывы: