Siemens Drager medical Carina Скачать руководство пользователя страница 109

Страница: 109 / 144

Instructions for Use Carina SW 3.n

109

Maintenance

Replacing the inlet filter

When the inlet filter is removed the »

Inlet filter

missing !!

« alarm is displayed.

Unlock the inlet filter, fold it down and remove it
from the holder. For disposal see page 112.

Insert a new inlet filter, swivel it in and

press at the top until its snaps into place.

Taking the device out of operation for
a lengthy period

Taking the device out of service

Switch off the device.

Disconnect cables and hoses.

Discard any disposable components and obtain
new disposable components.

Clean and disinfect reusable components.

Remove inlet filter, discard and obtain a new
inlet filter.

Storing the device

Only store the device under permissible ambient
conditions (see chapter "Technical Data" on
page 113).

WARNING
Do not operate the device without an inlet fil-
ter: risk of infection!

030

023

Содержание Drager medical Carina

















































































































































Результаты поиска

Содержание Drager medical Carina

Отзывы:

Siemens Drager medical Carina, Инструкция по эксплуатации, Страница: 109 / 144

Результаты поиска

Содержание Drager medical Carina

Отзывы: