Siemens Drager medical Carina Скачать руководство пользователя страница 84

Страница: 84 / 144

Monitoring

Instructions for Use Carina SW 3.n

Setting alarm limits

Press »

Select Menu

« button.

Press »

Alarms

« button.

Carina displays the alarm limits set.

The current measured value is displayed between
the upper and lower alarm limits.

To set:

Press the appropriate button.

Select the value using the rotary knob and con-
firm.

= Upper alarm limit
= Lower alarm limit

Alarm
limit

Setting range

Value set on
delivery

high

10 to 55 mbar

25 mbar

MV high

2 to 40 L/min

15 L/min

MV low

0.1 to 39 L/min

3 L/min

f high

10 to 50 bpm

20 bpm

apn

5 to 60 seconds

15 seconds

disconn

Mask: 0, 15, 30, 60, 90, 120 seconds
Tube: 0, 15, 30, 60 seconds

15 seconds

WARNING
Set the alarm limits according to the patient's
condition. Alarm conditions that are not
adapted to the patient may lead to no or false
alarms.

035

537

Содержание Drager medical Carina

















































































































































Результаты поиска

Содержание Drager medical Carina

Отзывы:

Siemens Drager medical Carina, Инструкция по эксплуатации, Страница: 84 / 144

Результаты поиска

Содержание Drager medical Carina

Отзывы: