manualshive.com logo in svg

Siemens Drager medical Carina, Инструкция по эксплуатации, Страница: 50 / 144

Поделиться
Скачать
Siemens Drager medical Carina Скачать руководство пользователя страница 50

50

Instructions for Use Carina SW 3.n

Preparation

O

2

 supply, connect

WARNING
Keep oil and grease away from all oxygen sup-
ply components. Risk of explosion due to 
spontaneous combustion!

WARNING
Smoking and naked flames prohibited: fire 
hazard.

WARNING
If inspiratory oxygen concentration differs 
from ambient air concentration, monitoring of 
inspiratory oxygen concentration with adjust-
able high and low alarm limits is needed. Con-
nect external monitor to hose system in 
accordance with ISO 21647. 
Otherwise no alarm will be activated if actual 
inspiratory oxygen concentration differs from 
set oxygen concentration.

WARNING
Patients depending on ventilation need either 
monitoring of expiratory tidal volume, or mon-
itoring of expiratory minute volume, or moni-
toring of endtidal expiratory CO

2

 

concentration. Connect appropriate external 
monitor to hose system. 
Otherwise no alarm will be activated, if 
patient's ventilation deteriorates.

WARNING
In the case of patients who require a high O

2

 

concentration ensure that there is backup 
oxygen supply available, e.g. in O

2

 cylinders.

WARNING
Make sure there is adequate ventilation at the 
rear of Carina. Do not use an O

2

 source which 

supplies a flow in excess of 10 L/min. 
Switch off the source, e.g. an O

2

 concentrator 

if Carina is not in ventilation mode. Otherwise 
there is an increased risk of fire due to the 
concentration of oxygen when heat/ignition 
and fuel are present.

Содержание Drager medical Carina

















































































































































Отзывы:

Нет отзывов