Siemens Drager medical Carina Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 144

Siemens Drager medical Carina Скачать руководство пользователя страница 104

Cleaning, Disinfection and Sterilisation

104

Instructions for Use Carina SW 3.n

General information on cleaning,
disinfection and sterilisation

z

Comply with the hospital's hygiene regulations!

z

Clean the device after every patient.

z

Whenever the Carina device, trolley, hinged
arm or gas supply hoses have been contami-
nated or potentially contaminated with body flu-
ids disinfect their surfaces with a suitable
disinfectant e.g. Virex Tb.

In the case of disposable components, observe the
manufacturer's recommendations. Replace dispos-
able components weekly or according to hospital
regulations.

WARNING
In case of potential contamination with body
fluids, clean and disinfect the device. Wear
protective clothing, goggles, disposable
gloves etc. Risk of infection for hospital staff
and other patients.

WARNING
Personnel should take precautions to avoid
direct contact with chemical disinfectants and
they should always be used in well-ventilated
areas. Material Safety Data Sheets (MSDS)
should be readily available in the event of
accidental exposure.

WARNING
Do not sterilise parts in ethylene oxide!
Ethylene oxide can diffuse into the parts.
Health hazard!

WARNING
Penetrating liquid may lead to failure of the
device or damage to the device and endanger
the patient! Do not spray the disinfectant
directly on the unit. Only disinfect parts by
wiping and make sure no liquids penetrate
into the device.

«
...
102
103
104
105
106
...
»

Содержание Drager medical Carina

















































































































































Отзывы:

Нет отзывов