Siemens Drager medical Carina Скачать руководство пользователя страница 105

Страница: 105 / 144

Instructions for Use Carina SW 3.n

105

Cleaning, Disinfection and Sterilisation

Care list

Dismantling the components

Switch off the device and respiratory gas
humidifier.

Disconnect mains plug.

Drain condensate from water traps.

Drain the water container of the humidifier.

Remove expiratory valve or leak valve. Remove
pilot line of the expiratory valve.

Remove the inlet filter of the basic device.

Respiratory gas humidifier, medication
nebulizer

Dismantle according to the relevant instructions
for use.

Ventilation hoses

Remove from the nozzles.

To remove the ventilation hoses, always
hold them at the connection sleeves and not
the spiral ribbing!

Otherwise the spiral ribbing may become
detached, e.g. at the connection sleeve, or the
hose can be torn out of the sleeve.

Drain condensate from ventilation hoses.

Disinfect and clean ventilation hoses, water
traps and their removed collecting jars.

What
Cleanable components

How often
Recommended cleaning
intervals

How

Carina basic device

per patient

Dismantle, clean and if applicable wipe
disinfect

Trolley
Compressed gas hose
Hinged arm

per patient

Dismantle, clean and if applicable wipe
disinfect

Reusable ventilation hoses
Reusable water trap

per patient/weekly

Dismantle, clean and disinfect in the
cleaning and disinfection machine at
93 °C/10 minutes with detergents only.
Hot steam sterilisation at 134 °C.

048

084

Содержание Drager medical Carina

















































































































































Результаты поиска

Содержание Drager medical Carina

Отзывы:

Siemens Drager medical Carina, Инструкция по эксплуатации, Страница: 105 / 144

Результаты поиска

Содержание Drager medical Carina

Отзывы: