Sharp AR-BC320 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 344

Sharp AR-BC320 Скачать руководство пользователя страница 89

AR-BC320 DESCRIPTIONS OF EACH SECTION 7 - 48

b. Operation flowchart

[RADF mode (single-side copy mode) copying]

START

Step 01:

The transport section is closed.
(AOSW/FOS OFF)

Step 02:

An original is set in the original tray.
(EMPS output LOW)

Step 03:

Print SW ON.

(Preliminary feed): For the first original, dummy discharge

is performed.

Step 04:

Document feed motor (DFM) forward rotation.
(Pickup roller and document feed roller rotate.)
Original stopper is released, and original feed
starts.

Step 05:

Transport motor (DTM), delivery motor (DEM)
forward rotation.
(Transport belt and reverse roller rotate.)
*A: If there was an original already present in

the tray, it is discharged.

*A

Step 06:

Document exit sensor (DES) detects leading
edge of discharged original.
(DES output HIGH)

*A

Step 07:

Transport motor (DTM) and delivery motor
(DEM) rpm decrease.

Step 08:

Resist sensor (REGS) detects leading edge of
original.
(REGS output HIGH)

Step 09:

Original contacts resist rollers and stops.
Document feed motor (DFM) OFF.

Step 10:

Document feed motor (DFM) reverses
direction.
(Resist rollers rotate.)
The leading edge of the original is taken up by
the resist rollers.

Step 11:

Original timing sensor (TIMS) detects leading
edge of original.
(TIMS output HIGH)

Step 12:

Document feed motor (DFM) OFF.
(The original is stopped with its leading edge
taken up by the resist rollers.)

*A

Step 13:

Document exit sensor (DES) detects trailing
edge of discharged original.
(DES output LOW)

*A

Step 14:

Original is discharged.

Step 04

Step 05

Step 06

Step 07

Step 08

Step 09

Step 10

Step 11

Step 12

Step 13

Step 14

«
...
87
88
89
90
91
...
»

Содержание AR-BC320

























































































































































































































































































































































Отзывы:

Нет отзывов