manualshive.com logo in svg

Sharp AR-BC320, Руководство по обслуживанию, Страница: 234 / 344

Поделиться
Скачать
Sharp AR-BC320 Скачать руководство пользователя страница 234

AR-BC320  SIMULATION  9 - 80

When the printer Flash data are normally cleared, "COMPLETE" is 
displayed. In case of an error, "ERROR" is displayed.

1. Press [EXECUTE] key. (A3 or 11" x 17" paper is automatically 

selected.)
The color patch image (adjustment pattern) is printed out.

2. Set the color patch image (adjustment pattern) printed in 

procedure 1) on the document table.

3. Press [FACTORY] key on the operation panel, and press 

[EXECUTE] key.
The printer color balance adjustment (step 1) is automatically 
performed and the color balance check patch image is printed 
out.

4. Press [REPEAT] key.
5. Press the [EXECUTE] key.

The color patch image (adjustment pattern) is printed out.

6. Set the color patch image (adjustment pattern) printed in 

procedure 5) on the document table. (Set the image so that the 
higher-density area comes on the paper exit side.)

7. Press [FACTORY] key on the operation panel, and press 

[EXECUTE] key.
The printer color balance adjustment (step 2) is automatically 
executed, and the color balance check patch image is printed 
out.

8. Press [OK] key on the operation panel. Initial setting of half-

tone image connection is executed according to  the 
adjustment data.

When this function is executed:
When installing (including the AR-PK4), when replacing 
consumable parts (Drum cartridge, TN cartridge, transfer belt), 
when changing to "1" with SIM 26-54, when the screen is switched 
with SIM 67-29, or when there is a great change in color.

∗

Execute after the automatic adjustment (SIM 46-24) of copy.

3. Enter a set value with the 10-key, and press [OK] key. (When 

[v]/[^] key is pressed, the set value is increased or decreased 
in the increment of 1.
[OK] key is highlighted and the set value is saved to the 
backup area and the RAM. Sending is made to the printer 
controller.
After completion of sending, [OK] key is returned to the normal 
display.

4. Press the [EXECUTE] key.

[EXECUTE] key is highlighted, and self-print is executed.
After completion of the operation, [EXECUTE] key is returned 
to the normal display. 

Common to KCMY

67

-18

Purpose

Data clear

Function 
(Purpose)

Used to clear the Flash data. (Printer)

Section

Printer

Item

Others

Operation/
Procedure

1. Press the [EXECUTE] key.

The confirmation message to clear the Flash 
data is displayed.

2. Select YES/NO to clear the Flash data.

YES: Clear
NO: Not clear

67

-24

Purpose

Adjustment

Function 
(Purpose)

Used to adjust half-tone density of the printer engine 
automatically.

Operation/
Procedure

1. Select a color to be set. 
2. Select an item to be set.

67

-25

Purpose

Adjustment

Function 
(Purpose)

Printer engine color balance manual correction: PG 
print (Used to perform a fine adjustment of color 
from the adjustment of SIM 67-24.)

Operation/
Procedure

1. Select a color to be set.
2. Select an item to be set.

Item

Set range

Default

A

POINT1

1 – 99

50

B

POINT2

1 – 99

50

C

POINT3

1 – 99

50

D

POINT4

1 – 99

50

E

POINT5

1 – 99

50

F

POINT6

1 – 99

50

G

POINT7

1 – 99

50

H

POINT8

1 – 99

50

I

POINT9

1 – 99

50

J

POINT10

1 – 99

50

K

POINT11

1 – 99

50

L

POINT12

1 – 99

50

M

POINT13

1 – 99

50

N

POINT14

1 – 99

50

O

POINT15

1 – 99

50

67

-26

Purpose

Adjustment

Function 
(Purpose)

Used to select the target value of the referenced 
scanner in the printer engine automatic density 
adjustment. (The target value set with SIM 67-24 
and the gray balance can be adjusted.)

Operation/
Procedure

Select a target value (set value). The selected target 
value (set value) is highlighted.

Content of item

Set value

Default

Target value table setting

DEF1, DEF2, DEF3

DEF1

Содержание AR-BC320

























































































































































































































































































































































Отзывы:

Нет отзывов