manualshive.com logo in svg

Sharp AR-BC320, Руководство по обслуживанию, Страница: 175 / 344

Поделиться
Скачать
Sharp AR-BC320 Скачать руководство пользователя страница 175

AR-BC320  SIMULATION  9 - 21

After 10 sec, the scanner lamp is turned OFF. At that time, the 
[EXECUTE] key returns to the normal display.

2. When the [EXECUTE] key is pressed, the key is highlighted 

and the selected discharge lamp is lighted for 30sec. If the 
[EXECUTE] key is pressed while the lamp is lighted, the lamp 
is turned OFF.

2. Press the [EXECUTE] key. The selected load starts the 

operation. During the operation of the load, the [EXECUTE] 
key is highlighted. If the [EXECUTE] key is pressed while it is 
highlighted, the operation is stopped.

(Loads to be selected)

∗

When BLUM is ON, the belt moves up.
When BLUM is OFF, the belt moves down.

2. Press the [EXECUTE] key.

The selected load is operated. During operation, the 
[EXECUTE] key is highlighted. If the [EXECUTE] key is 
pressed while it is highlighted, the operation is stopped.

(Loads to be selected.)

5

-3

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of the scanner lamp 
and its control circuit.

/

Section

Scanner (Image scanning)

Item

Operation

Operation/
Procedure

When the [EXECUTE] key is pressed, the scanner 
lamp is lighted for 10 sec. While the scanner lamp is 
lighted, the [EXECUTE] key is highlighted. If the 
[EXECUTE] key is pressed under this state, the 
lamp is turned OFF.

5

-4

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of the discharge lamp 
and its control circuit. 

/

Section

Process (Photoconductor, developing, 
transfer, cleaning)

Others

Item

Operation

Operation/
Procedure

1. Select the target discharge lamp with the [K], 

[C], [M], and [Y] keys. 
(K: Black, C: Cyan, M: Magenta, Y: Yellow)

6

6

-1

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of the loads (clutches 
and solenoids) in the paper transport system, 
transfer, and fusing, and the control circuit.

Section

Paper transport (paper exit, switchback, transport), 
transfer, fusing

Item

Operation

Operation/
Procedure

1. The names of the loads that can be checked are 

displayed. Select the load to be checked with the 
key, and the selected load is highlighted.

CPFC

Cassette transport clutch

TRC

Cassette paper feed clutch

MTRC

Manual paper feed clutch

MPFC

Manual transport clutch

GSS

Paper exit gate select solenoid

RRM

Resist roller motor (PSM)

PFM

Paper feed motor (Vertical transport)

FUM

Fusing motor

BLUM

Lift motor

BLUM (R)

∗

Lift motor (Reverse rotation/waste toner transport 
motor)

OSM

Offset motor (Job separator)

CARB

Calibration plate

6

-2

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of the fan motors and 
the control circuits.

Section

Others

Item

Operation

Operation/
Procedure

1. The loads that can be checked are displayed. 

Select one to be checked.

VFM1

Fusing fan 1

VFM2

Fusing fan 2

PSFM

Power fan

PRTCFM

Process exhaust fan

SIROCCOFM

SIROCCO fan

7

7

-1

Purpose

Setting/Operation test/check

Function 
(Purpose)

Used to set the aging conditions.

Item

Operation

Operation/
Procedure

1. Press each corresponding key to set for the 

aging operation.
(Set items of each key)
The selected key is highlighted.

Содержание AR-BC320

























































































































































































































































































































































Отзывы:

Нет отзывов