Sharp AR-BC320 Скачать руководство пользователя страница 272

Страница: 272 / 344

AR-BC320 TROUBLESHOOTING 11 - 25

Main
code

Sub

code

Title

ADU alignment plate operation
abnormality

Display

Lamp/Message

Phenomenon Detail

The alignment plate does
not move from the home
position within 1sec when
it must move. Return to the
home position is not
detected for 5sec or more.

Section

ADU

Case 1

Cause

Home position sensor
trouble

Check &
Remedy

Use SIM 9-2 to detect the
home position sensor.

Case 2

Cause

Alignment plate shift motor
trouble

Check &
Remedy

Use SIM 9-4 to check the
alignment plate operation.

Case 3

Cause

Disconnection of the
harness between the ADU
control PWB and the motor
sensor.

Check &
Remedy

Check connection of the
harness between the ADU
control PWB and the motor
sensor.

Case 4

Cause

Alignment plate operation
belt, gear breakage or
improper adjustment

Check &
Remedy

Remove the ADU, and
check for breakage of the
gear and the belt.

Main
code

Sub

code

Title

ADF communication trouble

Display

Lamp/Message

Phenomenon Detail

Communication test error
when turning on the power
or after canceling the
exclusive simulation.
Communication error with
the ADF

Section

ADF

Case 1

Cause

Improper connection or
disconnection of the
connector and the harness

Check &
Remedy

Check the connector and
the harness in the
communication line.
Turn OFF/ON the power to
cancel the error.

Case 2

Cause

ADF control PWB trouble,
control PWB (MFP)
trouble, malfunction
caused by noises

Check &
Remedy

Check the ADF control
PWB and the control PWB
(MFP).
Turn OFF/ON the power to
cancel the error.

Main
code

Sub

code

Title

ADF resist sensor trouble

Display

Lamp/Message

Phenomenon Detail

ADF resist sensor
detection trouble

Section

ADF

Case 1

Cause

Sensor trouble

Check &
Remedy

Use SIM 2-2 to check the
resist sensor detection.

Case 2

Cause

Disconnection of the
harness in the ADF.

Check &
Remedy

Check the harness in the
ADF.

Case 3

Cause

ADF control PWB trouble

Check &
Remedy

Replace the ADF control
PWB.

Main
code

Sub

code

Title

ADF repulsion sensor trouble

Display

Lamp/Message

Phenomenon Detail

ADF paper feed/reverse
sensor detection trouble

Section

ADF

Case 1

Cause

Sensor trouble

Check &
Remedy

Use SIM 2-2 to check the
resist sensor detection.

Case 2

Cause

Disconnection of the
harness in the ADF.

Check &
Remedy

Check the harness in the
ADF.

Case 3

Cause

ADF control PWB trouble

Check &
Remedy

Replace the ADF control
PWB.

Main
code

Sub

code

Title

ADF timing sensor trouble

Display

Lamp/Message

Phenomenon Detail

ADF timing sensor
detection trouble

Section

ADF

Case 1

Cause

Sensor trouble

Check &
Remedy

Use SIM 2-2 to check the
resist sensor detection.

Case 2

Cause

Disconnection of the
harness in the ADF.

Check &
Remedy

Check the harness in the
ADF.

Case 3

Cause

ADF control PWB trouble

Check &
Remedy

Replace the ADF control
PWB.

Main
code

Sub

code

Title

Paper feed motor operation
abnormality

Display

Lamp/Message

Phenomenon Detail

Paper feed motor
operation abnormality

Section

ADF

Case 1

Cause

Motor lock, motor RPM
abnormality, Over current
to the motor, ADF control
PWB trouble

Check &
Remedy

Use SIM 2-2/3/4 to check
the paper feed motor
operation.

Содержание AR-BC320

























































































































































































































































































































































Результаты поиска

Содержание AR-BC320

Отзывы:

Sharp AR-BC320, Руководство по обслуживанию, Страница: 272 / 344

Результаты поиска

Содержание AR-BC320

Отзывы: