manualshive.com logo in svg

Sharp AR-BC320, Руководство по обслуживанию, Страница: 147 / 344

Поделиться
Скачать
Sharp AR-BC320 Скачать руководство пользователя страница 147

AR-BC320  SETTING AND ADJUSTMENTS  8 - 40

9) Press the [EXECUTE] key.

The [EXECUTE] key is highlighted. Then it returns to the nor-
mal display. The manual paper feed guide minimum width
position detection level is recognized.

If the above procedure is not completed normally, "ERROR" is
highlighted. If the above procedure is completed normally, the
above data are stored and "COMPLETE" is highlighted.

This adjustment must be performed in the following cases:

• When the operation panel is replaced.

• When a U2 trouble occurs.

• When the MFP PWB is replaced.

• When the EEPROM of the MFP PWB is replaced.

1) Enter the SIM 65-1 mode.

2) Touch the four cross marks on the display.

When the cross marks are pressed, the buzzer sounds and
they are changed into gray display. When the touch panel
adjustment is completed by pressing all the four marks, the
display returns to the simulation sub code number entry menu.

If there is any abnormality, the first display is shown again.

∗

When touching the crosses, never use a needle or a pin with a
sharp point.

This adjustment must be performed in the following cases:

• When a part in the DC power unit is replaced.

1) Put the multi-meter on the 3.4V line of the DC main PWB and

GND.

2) Turn VR701 on the DC main PWB to adjust so that the voltage

is 3.4V.

1) Put the multi-meter on the 5.0V line of the DC main PWB and

GND.

2) Turn VR702 on the DC main PWB to adjust so that the voltage

is 5.0V.

1) Enter the SIM 50-27 mode.

2) Select the adjustment mode with the scroll key.

3) Enter the adjustment value at the selected point with the 10-

key and press the OK key to set the entered adjustment value.

When the adjustment value is changed, the image losses at the
four corners are changed uniformly.

A. W-RADF hinge section detail

ADJ 16

Touch panel coordinates 
setting

ADJ 17

Power voltage adjustment

VR701

VR702

ADJ 17A

3.4 V power voltage adjustment

ADJ 17B

5.0 V power voltage adjustment

ADJ 18

FAX/scanner mode image loss 
adjustment

Display

Content

Min. 

Value

Max. 

Value

Default

A

FAX MODE image loss

0

99

20

B

PUSH SCAN MODE image loss

0

99

30

C

PULL SCAN MODE image loss

0

99

0

ADJ 19

RADF adjustment

ADJ 19A

ADF adjustment (skew adjustment)

B

A

RADF 
securing 
screw

Right hinge 
assembly

Left hinge 
assembly

RADF

PPC

B

A

Hinge base

Nut

Screw adjustment screw

Right hinge 
assembly

RADF securing screw

(1 mm gradations)

Hinge base alignment scale line 

Auxiliary view Z

Z

Содержание AR-BC320

























































































































































































































































































































































Отзывы:

Нет отзывов