manualshive.com logo in svg

Sharp AR-BC320, Руководство по обслуживанию, Страница: 179 / 344

Поделиться
Скачать
Sharp AR-BC320 Скачать руководство пользователя страница 179

AR-BC320  SIMULATION  9 - 25

(Check item)

While the load operates, the [EXECUTE] key is highlighted.
When the [EXECUTE] key is pressed under this state, the 
operation of the load can be interrupted.

(Trouble codes to be canceled)

9

9

-2

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operation of the sensors and 
detectors in the inverter/duplex section and the 
control circuit.

Section

Inverter/Duplex

Item

Operation

Operation/
Procedure

The operations of sensors and detectors in the 
inverter/duplex section are displayed.
The active sensors and detectors are highlighted.

BPPD1

Inverter transport detection 1

BPPD2

Inverter transport detection 2

BPRD

Inverter reverse detection

BPOD

Inverter paper exit detection

BPFD

Inverter full detection

BDD1

Inverter door detection 1

BDD2

Inverter door detection 2

APPD1

ADU transport detection 1

APPD2

ADU transport detection 2

APHPS

ADU alignment plate home position

POD1

Machine paper exit detection

BYSET

Inverter installation detection

ADUDSET

ADU installation detection

ADUSET

ADU door open/close detection

9

-3

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of the loads (motor, 
clutch, solenoid) in the inverter/duplex section and 
the control circuits.

Section

Inverter/Duplex

Item

Operation

Operation/
Procedure

1. Select the load to be checked with the 10-key 

pad.

2. Press the [EXECUTE] key.

The load selected in procedure 1 operates.

BIM

Inverter paper entry motor

BRMFW

Inverter reverse motor (Normal rotation)

BRMRV

Inverter reverse motor (Reverse rotation)

BGSOL

Inverter gate solenoid

BTMFW

Inverter transport motor (Normal rotation)

BTMRV

Inverter transport motor (Reverse rotation)

ATM

ADU transport motor

APAM

ADU alignment motor

ATRC

ADU transport clutch

14

14

-0

Purpose

Clear/cancel (Trouble etc.)

Function 
(Purpose)

Used to cancel self diag troubles H3, H4, and H5. 
Inhibition of the color copy mode operation is 
canceled.

Item

Trouble

Error

Operation/
Procedure

1. Press the [EXECUTE] key. (YES/NO key 

display)

2. When YES key is pressed, the following troubles 

are cleared. (Cancel with NO key.)

Target trouble 

codes

Descriptions

H3-00

Heat roller high temperature detection (HL1)

H3-01

Heat roller high temperature detection (HL2)

H4-00

Heat roller low temperature detection (HL1)

H4-01

Heat roller low temperature detection (HL2)

H5-01

Five continuous detections of POD1 not-
reached jam

15

15

-0

Purpose

Clear/cancel (Trouble etc.)

Function 
(Purpose)

Self diag U6-09 (large capacity paper feed tray) 
trouble cancel

Section

Paper feed

Item

Trouble

Error

Operation/
Procedure

Press the [EXECUTE] key to cancel the trouble.

∗

Press the [CLOSE] key to terminate the 
simulation.

Содержание AR-BC320

























































































































































































































































































































































Отзывы:

Нет отзывов