Sharp AR-BC320 Скачать руководство пользователя страница 231

Страница: 231 / 344

AR-BC320 SIMULATION 9 - 77

(Settable ports)

3. Check sum is executed and the write result is displayed.

(Check sum result display)

-31

Purpose

Setting

Function
(Purpose)

Used to set ON/OFF of each port for output to the
TEL/LIU. (When the FAX is installed.)

Section

FAX

Item

Operation

Operation/
Procedure

1. Press the [EXECUTE] key. (ON: Reverse

display)

2. Press the [EXECUTE] key. (Setting is saved.)

MPXA

CION
MR

CML
DP

-32

Purpose

Operation test/check

Function
(Purpose)

Used to check (compare) the received data (fixed
data) from the line to make judgment of error or
normal. (When the FAX is installed.)

Section

FAX

Item

Operation

Operation/
Procedure

The fixed data received from the line are checked
and the result is displayed.
Coincide: OK is displayed. /
Not coincide: NG is displayed.

-33

Purpose

Operation test/check

Function
(Purpose)

Used to detect signals (BUSY TONE/CNG/CED/
FNET) from the line. (When the FAX is installed.)

Section

FAX

Item

Operation

Operation/
Procedure

Various signals are detected with the line
connected.
The detected signals are highlighted.

-34

Purpose

Operation test/check

Function
(Purpose)

Used to display the time required for sending the
test image data. (When the FAX is installed.)

Section

FAX

Item

Operation

Operation/
Procedure

The send test is executed, and the time to send the
image data in that test communication is measured
and displayed.
Send/receive are executed in the normal mode, and
the measure communication time (ms) is displayed.

-35

Purpose

Setting

Function
(Purpose)

Used to rewrite the Modem program.
(When the FAX is installed.)

Section

FAX

Item

Data

Writing

Operation/
Procedure

1. Press the [EXECUTE] key. (YES/NO key display)
2. Press [Yes] key to rewrite the Modem program.

(Press [NO] to cancel.)

COMPLETE : Write complete
81

: Check sum error

: Write error

: Delete error

: Verify error

: Because of LOADER NG

-36

Purpose

Operation test/check

Function
(Purpose)

Used to check send/receive (data/command line)
from the Modem controller to the MFP controller.
(When the FAX is installed)

Section

FAX

Item

Operation

Operation/
Procedure

1. Press [EXECUTE] key to check send and receive

operation of the data line or the command line
individually from the Model controller to the MFP
controller.

Содержание AR-BC320

























































































































































































































































































































































Результаты поиска

Содержание AR-BC320

Отзывы:

Sharp AR-BC320, Руководство по обслуживанию, Страница: 231 / 344

Результаты поиска

Содержание AR-BC320

Отзывы: