manualshive.com logo in svg

Sharp AR-BC320, Руководство по обслуживанию, Страница: 268 / 344

Поделиться
Скачать
Sharp AR-BC320 Скачать руководство пользователя страница 268

AR-BC320  TROUBLESHOOTING  11 - 21

Main 
code

Sub 

code

Title

Paper feed motor lock trouble

L4

02

Display

Lamp/Message

Phenomenon Detail

In warm-up, or in canceling 
a jam, the paper feed 
motor is rotated, and the 
lock signal is not detected 
within 1sec.

Section

Paper feed

Case 1

Cause

Paper feed motor trouble, 
disconnection of the 
harness between the PCU 
PWB and the paper feed 
motor, control circuit 
trouble

Check & 
Remedy

Use SIM 6-1 to check the 
paper feed motor 
operation. Check the 
harness and the connector 
between the PCU PWB 
and the paper feed motor.

Main 
code

Sub 

code

Title

Transfer belt lift motor trouble

L4

06

Display

Lamp/Message

Phenomenon Detail

When the belt motor lifts 
up or down, the change in 
the belt home position 
sensor characteristics is 
not detected within the 
specified time. 
(When the motor lifts up, 
the lower limit sensor 
remains ON after the 
specified time.)
(When the motor lifts 
down, the lower limit 
sensor does not turn on 
after the specified time.)

Section

Paper feed

Case 1

Cause

Belt lift motor trouble, 
disconnection of the 
harness between the PCU 
PWB and the belt lift 
motor, control circuit 
trouble

Check & 
Remedy

Use SIM 6-1 to check the 
belt lift motor operation. 
Check the harness and the 
connector between the 
PCU PWB and the belt lift 
motor.

Main 
code

Sub 

code

Title

Transfer belt motor trouble

L4

07

Display

Lamp/Message

Phenomenon Detail

1) Before driving the drum, 

the calibration plate is 
opened with the 
process control BK 
sensor, and light is 
emitted with the gain 
value of 0 and with the 
light emitting quantity 
fixed to 120. The 
average of ten light 
quantities repeats to be 
5 or less for 3 times 
continuously.

2)  Immediately after 

driving the drum, the 
calibration plate is 
opened with the 
process control BK 
sensor, and one whole 
turn of the belt surface 
is scanned with the gain 
value of 0 and with the 
light emitting quantity at 
the optimum value (120 
– 50). The difference 
between the max. value 
and the min. value of 
the scanned data is 5 or 
less.

Section

Paper feed

Case 1

Cause

Transfer belt motor 
connector disconnection, 
process control sensor 
connector disconnection, 
process control BK sensor 
defect, defective 
connection of the harness 
between the PCU PWB 
and the transfer belt motor, 
defective control circuit

Check & 
Remedy

Check the transfer belt 
motor operation with 
SIM25-1. Check the 
process control sensor 
operation with SIM44-2. 
Check the harness and the 
connector between the 
PCU PWB and the transfer 
belt motor.

Содержание AR-BC320

























































































































































































































































































































































Отзывы:

Нет отзывов