manualshive.com logo in svg

Sharp AR-BC320, Руководство по обслуживанию, Страница: 171 / 344

Поделиться
Скачать
Sharp AR-BC320 Скачать руководство пользователя страница 171

AR-BC320  SIMULATION  9 - 17

C. Details

Scanning is performed at the magnification ratio set in procedure 1 
is executed.

During scanning, the [EXECUTE] key is highlighted. If the 
[EXECUTE] key is pressed under this state, the operation is 
interrupted.

After completion of scanning, the [EXECUTE] key returns to the 
normal display.

To resume scanning, start with procedure 2. To change the 
magnification ratio, start with procedure 1.

Scanning is performed at the max. scanning length (432 mm). If, 
however, the magnification ratio is set to a value greater than 
100% in procedure 1, the scanning length is changed accordingly.

The active sensors and detectors are highlighted.

• The light source unit is at the home position. a MHPS is 

highlighted.

• The light source unit is not at the home position. a MHPS is 

displayed normally.

2. Select the scan mode (Color / B/W).
3. Press the [EXECUTE] key.

Scanning is repeated under the conditions set in procedures 1 
and 2.
During scanning, the [EXECUTE] key is highlighted.

Scanning is repeatedly performed until the [EXECUTE] key or the 
interruption key is pressed.

Aging of the document feeder is executed under the conditions 
specified with procedure 1. During aging, the [EXECUTE] key is 
highlighted. If the [EXECUTE] key is pressed while it is 
highlighted, the operation is interrupted.

To resume aging, execute with procedure 1. To change the 
conditions for aging, execute with procedure 1.

1

1

-1

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of the scanner unit 
and its control circuit.

Section

Scanner (Image scanning)

Item

Operation

Operation/
Procedure

1. Select the copy (scanning) magnification ratio 

with the zoom key. The magnification ratio can 
be increased or decreased with the [ZOOM] key 
by the increment of 1%. The selected 
magnification ratio is displayed on the 
magnification ratio display.

2. Press the [EXECUTE] key.

1

-2

Purpose

Operation test/check

Function 
(Purpose)

Used to check the sensors and detectors in the 
scanner section and the related circuits.

Section

Scanner (Image scanning)

Item

Operation

Operation/
Procedure

The operations of sensors and detectors in the 
scanner section are displayed.

1

-5

Purpose

Operation test/check

Function 
(Purpose)

Used to check the scanner (scanning) unit and its 
control circuit.

Section

Scanner (Image scanning)

Item

Operation

Operation/
Procedure

1. Select the copy (scanning) magnification ratio 

with the key (touch panel).  The magnification 
ratio can be increased or decreased with the 
[ZOOM] key by the increment of 1%.
The selected magnification ratio is displayed on 
the magnification ratio display.

2

2

-1

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of the RADF unit and 
the control circuit. (The document feed operation is 
repeatedly performed.)

Section

RADF

Item

Operation

Operation/
Procedure

1. Select the aging mode with the key. When 

selection is made, the selected item is 
highlighted.
[1:SIDE]: Single copy aging mode
[2:SIDE]: Duplex copy aging mode

2. Press the [EXECUTE] key.

Содержание AR-BC320

























































































































































































































































































































































Отзывы:

Нет отзывов