SEW-Eurodrive MOVI-PLC Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 108

SEW-Eurodrive MOVI-PLC Скачать руководство пользователя страница 67

Manual – MOVI-PLC® Application Solution "SyncCrane"

67

6

Emergency mode

Operation

6.7

Emergency mode

Interface description

Mode selection

PO1:Bit11 = TRUE
PO1:Bit12 = FALSE
PO1:Bit13 = TRUE

Jog +

PO1:9

Jog–

PO1:10

Axis number

PO3 Broadcast 99 or single axis mode 1 ... 12

Velocity specification

PO8 in [rpm] or [user units]

Velocity limit

Startup parameter

Ramp specification

PO9 Acceleration ramp in [ms]
PO10 Deceleration ramp in [ms]

Digital input

You can influence the emergency mode by activating the digital input
"SetEmergencyMode-DI01 X31:4":
•

DI01 SetemergencyMode =

False

: The position-controlled procedure

switches the inverter to "speed specification" mode.

•

DI01 SetemergencyMode =

True

: The position-controlled procedure

switches the inverter to "speed specification" mode and disables the
external encoder or absolute encoder, if installed. In this way, the
drive can even be moved with a defective absolute encoder.

Brief description

If emergency mode was activated using the user interface, the drive can
also be moved in the event of an encoder error.

Prerequisite

•

Operating mode is selected

•

Drive is enabled

•

MOVI-PLC

®

was restarted

Functional
description

The direction is selected using Jog+ or Jog-.
The travel movement is triggered by a specified
speed. Once emergency mode is selected using the
ApplicationBuilder startup, other operating modes
cannot be selected any longer.
The drive stops with position control if the direction
selection is not enabled or both directions are
selected at the same time.
The specified ramp time is used for accelerating/
decelerating the drive.
The specified velocity of the jog mode is compared
to the velocity limit and limited if necessary.
Automatic mode cannot be selected anymore when
the digital input (set emergency mode DI01 X31:4) is
activated.

«
...
65
66
67
68
69
...
»

Содержание MOVI-PLC













































































































Отзывы:

Нет отзывов