Seneca S6001 Скачать руководство пользователя

Страница: 85 / 122

Doc. MI004620-I

S6001 Pump controller

Rev. 0

www.seneca.it

85 /

122

BE REPRODUCED WITHOUT PREVIOUS AUTHORIZATION.

User Manual

I/O

Possible configuration

Configuration description

AO01-AO02

None

The input is free, non configured.

Reserved

In the system configuration currently in use, the

input is non-configurable.

Control from internal PID

Inverter control output (comes directly from the

PID system controller).

Repetition of analogue Input 1

Repetition of analogue Input 1.

Repetition of analogue Input 2

Repetition of analogue Input 2.

Repetition of analogue Input 3

Repetition of analogue Input 3.

Repetition of analogue Input 4

Repetition of analogue Input 4.

Generic inverter set reference repetition (Hz)

Repetition of the inverter control output signal.

Inverter frequency feedback repetition (Hz)

Repetition of the frequency feedback signal in

put from the inverter.

Tab. 67

Analogue I/O configurations

1.1.8.4 “HMI properties” screen

There are 2 “HMI properties” screens. To toggle from one screen to the other, press the

key.

Fig. 70 “HMI 1 properties” screen

Содержание S6001

























































































































Результаты поиска

Содержание S6001

Отзывы:

Похожие инструкции для S6001

Бренды по названию

Популярные бренды

Seneca S6001, Руководство пользователя

Результаты поиска

Содержание S6001

Отзывы:

Похожие инструкции для S6001

Бренды по названию

Популярные бренды