SciCan STATIM 7000 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 65

SciCan STATIM 7000 Скачать руководство пользователя страница 63

STATIM 7000 Service Manual – Calibration

61

continue (default password is: Unwrapped, Wrapped, R&P and Stop keys pressed in
this order). The service technician can change this password. In case the changed
password is lost a backdoor password can be used: Unwrapped, Wrapped,
Unwrapped, Wrapped in this order.

Keypad functions at this time

:

Unwrapped Key:

Select next item in the menu.

Wrapped Key:

Select previous item in the menu.

Rubber and Plastic Key:

Enter current selection

Toggle using keypad through the menu selection to reach Calibration option and
press R&P key.

5. Confirm that the display appears similar to the example above.

CHAMBER CALIBRATION:

(Voltage reading and Chamber thermocouple)

6. Press the Unwrapped cycle button (first from the left) and after that press START

button to activate a chamber thermocouple calibration cycle. The calibration cycle will
start by entering the heating up phase and the screen will change for the

Voltage

Reading calibration

(see screen below):

Screen Representation

VVV = Voltage measured by unit
CCC = Voltage calibration offset.

Keypad functions at this time

Unwrapped

Increase current field

Wrapped

Decrease current field

Rubber and Plastics

Select and return to main menu

Stop

Exit, without saving, to normal mode of operation

VVV CVO TTT CO

DDD

Chamber
thermocouple

hexadecimal offset

Chamber

temperature in ºC

Difference between
Va l idation TC and chamber

temperatures in ºC

Va l idation thermocouple

hexadecimal offset

compared

with chamber reading

Va l idation
thermocouple

reading

Voltage Calibration

V=VVV VCAL=CCC

«
...
61
62
63
64
65
»

Содержание STATIM 7000


































































Отзывы:

Нет отзывов