SciCan STATIM 7000 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 65

SciCan STATIM 7000 Скачать руководство пользователя страница 31

STATIM 7000 Service Manual –

Chamber Thermocouples

29

13.2 Chamber Thermocouple (Outlet)

1. Power

OFF

the unit, unplug it and remove the cover. See Cover. NOTE:

The steam generator may be hot if the unit has been operating.

2. Disconnect the fan connectors.

3. Disconnect the inlet and outlet tubes on the biological air filter.

4. Remove the rear chassis cover plate by removing the 3 screws across the

top and 3 screws across the bottom, and lifting the cover plate.

5. Remove the 2 screws that attach the chamber solenoid valve bracket to

the chassis.

6. Remove 2 screws on the under side of the unit that hold solenoid housing

to the chassis.

7. Disconnect the compression nut on

the copper tubing to the auxiliary

heater thermocouple, remove the

screws holding the chamber

solenoid valve base to the chassis

and slide the solenoid with the

copper tubing attached, to the left.

«
...
29
30
31
32
33
...
»

Содержание STATIM 7000


































































Отзывы:

Нет отзывов