Schmalz VacuMaster VM-BASIC Скачать руководство пользователя страница 46

Страница: 46 / 50

Maintenance

46 / 50

EN-US · 30.30.01.01610 · 00 · 01/20

NOTE

Moisture ingress

Damage to the electronics!

During cleaning, make sure that no moisture gets into the electronics.

•

The suction plates must be cleaned at least once per week with an agent containing active tensides
(pH-neutral).

•

Also clean mechanically (soft brush or ultrasonic cleaning).

•

Allow to dry at room temperature.

9.8 Replacing Suction Plates

1. Immediately replace damaged or worn suction plates or sealing lips (e.g. with cracks, holes or corru-

gation).

2. When replacing the sealing lip, make sure that the suction connection is not covered by the sealing

lip.

To unscrew the suction plate more easily, heat the screw union with a heat gun.

Screw in the new suction plate and reseal the connection while doing so.

Содержание VacuMaster VM-BASIC



















































Результаты поиска

Содержание VacuMaster VM-BASIC

Отзывы:

Похожие инструкции для VacuMaster VM-BASIC

Бренды по названию

Популярные бренды

Schmalz VacuMaster VM-BASIC, Руководство по эксплуатации

Результаты поиска

Содержание VacuMaster VM-BASIC

Отзывы:

Похожие инструкции для VacuMaster VM-BASIC

Бренды по названию

Популярные бренды